Questions quotated from forum
“when PCM reprogramming,i met Ford VCM2 IDS Error Code:11.0×0 851082,what’s wrong ? Any effective solutions ? Thanks for your help. “
Ford Check Engine Light Codes. Welcome to the Ford Check Engine Light codes page. Below you will find the most complete list of Ford trouble codes available. The code definitions are a good starting point when determining the cause of the service engine light but where do you go from there? G14 w 1 p & a code (bucket 129) for the dealer is different than the p & a code on the financial statement. Check dcs download file to verify p & a code is posted correctly (5 digit number example 582=00582) g20 ss 1 discounted notes receivable (non us) bucket 0007 has an invalid value. Bucket 0007 not equal 0 usa dealers cannot use. Ford Motor Corporation OBD I diagnostic. This page explains how to get the codes without any special tools. The codes are listed seperately based upon fuel delivery type. The codes are defined as to what system is affected. When possible we give the more descriptive name of the component and the more commonly known OBD II component name. Accessing Ford OBD1 Trouble Codes Using Analog Voltmeter. EEC-V, DI 7.3L Turbo Diesel & Villager. Connect analog voltmeter to data link connector located in engine compartment.
- OBD-II (Check Engine Light) Trouble Codes. Welcome to OBD-Codes.com, your headquarters for everything OBD-II related. For more information on what OBD codes are, OBD-II codes explained, explanation of fuel trims, or answers to other questions, visit our FAQ area.
- Ford Motor Company began its production activity, and as a result was created 'gasoline buggy' driven by a motor 8 hp, which received the name of 'Model A'. The focus in the 60s becomes young. In accordance with public sentiment, Ford quickly reorient their production to.
Well,this error usually resulted from the operation cannot begin because the PCM failed to complete a service procedure. You can Perform PMI on the PCM to resolve the issue this questions.And following are several workable methods that have been tested by forum members,i made a summary and post here for sharing
Solution 1 : Turn off your firewall . You should close the internet, anti-virus software before using.
Solution 2 : Uninstall fmp and reinstall it, Use 32 bit processor,because fmp would not work correctly with 64.
Solution 3 : If you are checking PCM for up-dates, Ford will advise on 6.0L powertrain if there is a reflash avail for TCM, FICM or PCM, if it states there is no update then all three modules are at latest level, no action required, I am aware it states to remove FICM relay prior to reflash FICM, this is a carryover note from when we used PDS or WDS to reflash the FICM, if you are using IDS with VMM interface its not required to remove the FICM relay, I have reflashed over 1000 of them this way over the last 7 years, as always make sure the battery stays in the sweet spot @ 13.5 volts, make sure your laptop has sufficient power, I always plug in, make sure cables to veh and laptop are safe from accidental disconnect, Good luck!
Solution 4 : If you try to VCM2 genuine or clone to make reprogaming well you need IDS V98.01 or higher.It would be good to check if during initiation programming interface output 18,5V on pin 13 in OBD connector.
How to reprogram PCM via IDS software :
Main procedure:
Step 1: Install a new PCM
Step 2: Reprogram PCM
Step 1: Install a new PCM
Install VMware and well setup IDS software follow the video/pdf guide (see attachment below)
Run Ford Module Programming
Click on car icon
Select “Start New Session”
Press “Confirm”
The SAE J2534 pass-thru device cables must not interfere the safe operation of the vehicle. Secure all cables away from the vehicle pedals.
Make connection as shown
Turn ignition to ON
Apply the parking brake
Apply Neutral/Park gear position
Establishing communication to PCM
Verify vehicle information
Press programming icon
Select “Module programming”
Select “Programmable Module Installation”>> “PCM”
Again verify vehicle information and confirm
Turn ignition to OFF position (Position 0)
Check if the displayed VIN is correct, if yes, hit Yes to continue
Follow the system prompt to install a new module in vehicle
Step 2: Reprogram PCM with VCM 2 IDS
Please read the following information carefully.
NOTE: Do not start a reprogramming session with a low battery in the vehicle and/or programming tool.
The fuel pump and the engine cooling fan(s) may run during the following procedure.
If you are programming a 6.0L diesel, the FICM replay must be removed before programming.
Turn ignition to ON position
Erase procedure in progress
Downloading data and reprogramming PCM in progress
Turn ignition to OFF
The operation in progress
Turn ignition to ON
Set ignition switch to OFF
Calibration has been loaded and checked.
' Ford Error Codes 'download 2017
If you programmed a 6.0L diesel please reinstall the FICOM relay.
Start engine. Do not depress the throttle pedal.
Set ignition to OFF
Set ignition to ON
Clear stored fault codes
Turn ignition to OFF
PCM reprogramming procedure is done.
24hour Online Customer Service:
Free Error Code Fix
E-mail:Autocardiag@gmail.com
Skype:AutoDiag
Whatsapp:86-13667154167